• <button id="te2zc"><acronym id="te2zc"><input id="te2zc"></input></acronym></button>
    <tbody id="te2zc"></tbody><em id="te2zc"><acronym id="te2zc"></acronym></em>
  • <dd id="te2zc"><noscript id="te2zc"></noscript></dd>
     歡迎訪問濟南科爾超聲波設備有限公司網站!

    專注生產工業用清洗設備

    讓工業清洗無難事

    電話

    業務咨詢電話:

    18663767799

    你所在位置: 首頁-新聞動態-常見問題-通過式清洗機操作工藝的具體使用事項
    常見問題

    通過式清洗機操作工藝的具體使用事項

    作者:guanli來源:http://www.a7f4.com/時間:2022-09-08

    隨著超聲波清洗機設備的應用范圍越來越廣泛,而通過式清洗機所采用的通過式清洗技術采用頻率28KHz的超聲波進行清洗,由噴淋系統、噴嘴旋轉裝置、磷化系統、自動溫控加熱系統、風切吹水系統等組成。對于某些特定的清洗對象,還配有熱空氣烘干、專用清洗架及清洗液的過濾循環系統。
    As the application range of ultrasonic cleaning machine equipment becomes wider and wider, the through cleaning technology adopted by the through cleaning machine uses 28kHz ultrasonic wave for cleaning, which is composed of spray system, nozzle rotating device, phosphating system, automatic temperature control heating system, air cutting and water blowing system, etc. For some specific cleaning objects, it is also equipped with hot air drying, special cleaning rack and cleaning liquid filtration and circulation system.
    通過式清洗機工作時,將料框置于輸送帶上,清洗工件裝于相對應的料框中,零件不得重疊,節拍為2-3min/筐;料筐依次通過清洗室、漂洗室、吹干、烘干室,完成全過程后自動輸出清洗潔凈的零件,如有水珠需進行人工補吹,將吹干后的零件放入防塵周轉箱。
    When the through type cleaning machine works, place the material frame on the conveyor belt, and install the cleaned workpiece in the corresponding material frame. The parts shall not overlap, and the beat is 2-3min/basket; The material basket passes through the cleaning room, rinsing room, drying room and drying room in turn. After the whole process is completed, the cleaned parts will be automatically output. If there are water drops, manual supplementary blowing is required. The dried parts will be put into the dust-proof turnover box.
    相比傳統的清洗設備,通過式清洗機的主要特點是不僅能有效的避免高光潔度物體的表面損傷;而且可除去附著在表面的亞微米大小的顆粒;甚至對浸入液體中,面向換能器的一面也能被洗凈,所以要進行兩面清洗。
    Compared with the traditional cleaning equipment, the main characteristics of the through type cleaning machine are that it can not only effectively avoid the surface damage of high finish objects; And can remove submicron sized particles attached to the surface; Even the side facing the transducer when immersed in liquid can be cleaned, so both sides should be cleaned.
    通過式清洗機
    操作通過式清洗機的時候,注意要將被清潔的零件要規整地放在運送帶上,不許壓在滾輪上;而且在運送帶上,被清潔的零件不能堆得過多,避免影響清潔作用,每個零件都能清潔到。
    When operating the through type cleaning machine, pay attention to placing the cleaned parts on the conveyor belt in an orderly manner, and do not press on the rollers; Moreover, on the conveyor belt, the cleaned parts cannot be stacked too much to avoid affecting the cleaning effect, and each part can be cleaned.
    通過式清洗機作業后,被清潔的零件不能停放在運送帶上,按中止按鈕,使全機中止運轉。清潔液應定時添加水和必定份額的金屬清潔劑以彌補耗費,使液面保持在必定高度,若是清潔作用達不到規則的技術需求時,應悉數替換清潔液。
    After the operation of the through type cleaning machine, the cleaned parts cannot be parked on the conveyor belt. Press the stop button to stop the whole machine. Water and a certain proportion of metal cleaner shall be added to the cleaning liquid regularly to make up for the consumption and keep the liquid level at a certain height. If the cleaning effect cannot meet the regular technical requirements, all the cleaning liquid shall be replaced.
    通過式清洗機操作工藝的具體使用事項就講解到這里了,以上內容您可以作為有關參考信息使用,當然要注意每日的檢查和定期的維修保養事項,更多注意就來我們網站www.a7f4.com咨詢吧!
    Here are the specific use matters of the operation process of the pass through washer. You can use the above contents as relevant reference information. Of course, you should pay attention to daily inspection and regular maintenance. For more attention, please come to our website www.a7f4.com!